Read an Index Contract Specification and Size a Trade
Scenario: your broker lists a stock index contract with these fields: price about 18,000, contract size 10 units, tick size 0.1, tick value 1 dollar, leverage 1 to 20. You have a 10,000-dollar account and want to risk 1 percent with a stop 50 points away.
Decode the specification. A contract size of 10 means one lot controls 10 units of the index. One full point of movement is worth 10 dollars per lot. A tick of 0.1 is worth 1 dollar, consistent with that.
Compute the risk per lot: 50 points times 10 dollars is 500 dollars. The risk amount is 100 dollars, so the lot size is 100 divided by 500, which is 0.2 lots.
Compute the notional value: 18,000 times 10 is 180,000 dollars per lot. At 0.2 lots, the notional is 36,000 dollars, 3.6 times the account.
Compute margin at 1 to 20: 180,000 divided by 20 is 9,000 dollars per lot, so 1,800 dollars for 0.2 lots, 18 percent of the account.
Now compare with a forex habit. A trader who typed 1.0 lots because it felt standard would face a risk of 500 dollars on that stop, 5 percent, and margin of 9,000 dollars, 90 percent of the account.
Always read three fields before sizing a new instrument: contract size, tick value, and margin.
Your turn: write the same calculation for any index your broker offers.
Read an Index Contract Specification and Size a Trade
Re: Read an Index Contract Specification and Size a Trade
The comparison with a forex habit is the most important warning. A trader used to forex, where 1.0 lots of EUR/USD is a standard size, might enter 1.0 lots on an index without thinking. On this contract, that's 180,000 dollars of notional, 500 dollars of risk on a 50 point stop, and 9,000 dollars of margin on a 10,000 dollar account. The margin alone would leave almost no room, and a normal move could trigger a margin call. Index contracts vary widely between brokers, so the specification must be read every time, even for a familiar index.
It’s Fairman 
-
Amanhasnoname
- Posts: 2060
- Joined: Fri Oct 30, 2026 9:45 am
Re: Read an Index Contract Specification and Size a Trade
This is the kind of check I wish I had done before my first index trade. I switched from forex to a German index on a demo and typed 1.0 lots as I always did, then saw the margin figure jump and the equity swing by more than I expected on one small candle. The contract size at that broker was 25 units, which I had never read.
Now I keep a small table in my notes for every instrument I trade, with contract size, tick value, minimum lot, margin per lot, and what a typical 20 point stop costs per lot. I fill it in from the platform's specification window, not from memory, because the same index can be set up differently at another broker.
The reply above made a good point that a normal move can trigger a margin call. I also check that margin after sizing stays under about a fifth of the account, so a gap on the open does not leave me exposed.
Now I keep a small table in my notes for every instrument I trade, with contract size, tick value, minimum lot, margin per lot, and what a typical 20 point stop costs per lot. I fill it in from the platform's specification window, not from memory, because the same index can be set up differently at another broker.
The reply above made a good point that a normal move can trigger a margin call. I also check that margin after sizing stays under about a fifth of the account, so a gap on the open does not leave me exposed.
Re: Read an Index Contract Specification and Size a Trade
Contract sizes for the same index can differ greatly between brokers. One broker might define one lot as 1 dollar per point, another as 10 dollars, and another as 25. Some use the index's own currency, so a German index contract might be priced in euros per point. The tick value and contract size fields in the specification give the answer. Checking one point's value in your account currency, as the post does, is the essential first step. A trader moving between brokers without checking could be trading ten or even twenty-five times their intended size.
It’s Fairman 
Re: Read an Index Contract Specification and Size a Trade
A 50 point stop on an index around 18,000 is about 0.28 percent of price, which is relatively tight for most major indices on a daily basis. Major US indices can move several hundred points on volatile days. So the stop should be based on the index's ATR rather than a round number. If the daily ATR is 250 points, a 50 point stop would be hit by normal noise on most days, which suggests it's suited to intraday trading. For swing trades, a wider stop with a smaller position would keep the risk at 1 percent while giving the trade more room.