Advertisement IC Markets

Rejection Blocks, Trading the Wick Zone

Discuss 1-minute to 15-minute price action setups, fading intraday momentum, key support/resistance zones, and proven short-term trading methodologies.
Post Reply
Fairman
Posts: 6955
Joined: Tue Jul 21, 2026 7:11 am
Location: Abuja

Rejection Blocks, Trading the Wick Zone

Post by Fairman »

Rejection Blocks, Trading the Wick Zone

Most traders mark order blocks using candle bodies. Rejection blocks flip that habit and focus on the wicks, the part of the candle that shows where price was pushed away.
diagram.png
diagram.png (36.57 KiB) Viewed 244 times
A rejection block forms when price makes a strong move into a level, leaves a long wick showing it was refused, and then reverses. The wick area becomes the zone of interest, because it marks where opposing orders were waiting.

How to identify one:

1. Find a swing high or swing low with an unusually long wick relative to the body.
2. Confirm that the wick formed at a meaningful location, such as after a liquidity sweep or at a higher-timeframe level.
3. Mark the wick area, from the tip of the wick to the edge of the body.
4. Wait for price to return to the zone later.

How to trade it:

- Look for a lower-timeframe reaction as price re-enters the wick zone.
- Place your stop beyond the extreme of the wick.
- Target the nearest opposing liquidity.

Why it can work: the long wick shows aggressive rejection. When price returns, traders who were trapped or who missed the first move often act again at the same area.

Caution: a wick alone isn't a setup. Without context, such as bias, liquidity, and structure, you'll mark rejection blocks everywhere and trade none of them well.

Practice by scrolling through your 1H chart and marking only the three most obvious wick rejections. Then watch how price treats them on the next visit.
It’s Fairman :geek:
Recommended broker for automated trading & scalping IC Markets
LondonNewsTrader
Posts: 421
Joined: Mon Sep 21, 2026 9:30 am

Re: Rejection Blocks, Trading the Wick Zone

Post by LondonNewsTrader »

Worth separating wicks made by structure from wicks made by a release. A long wick printed in the minute after a data surprise often reflects a liquidity gap and a spread blowout rather than orders waiting at that price, and the zone tends to get ignored when price comes back. I'd skip any wick whose timestamp matches a high-impact release and mark only the ones formed in normal trading.
FXS Prop Desk
Posts: 1692
Joined: Wed Oct 07, 2026 9:52 am

Re: Rejection Blocks, Trading the Wick Zone

Post by FXS Prop Desk »

Rejection blocks complement body-based order blocks well. A question worth testing: should the zone be the full wick, or only part of it, e.g. from the body to the 50% point of the wick? The full wick gives a wider zone and wider stop, with more fills; the half-wick version gives a better entry price but misses more trades.

Running both versions on the same set of swings over a few months shows which one has the better average R. It may differ between instruments, since gold's wicks tend to be longer relative to the body than EURUSD's.
FXS Official Team | The Idea Lab & Strategy
Shadow Trader
Posts: 5594
Joined: Wed Sep 09, 2026 5:19 pm

Re: Rejection Blocks, Trading the Wick Zone

Post by Shadow Trader »

For step 1, I found that unusually long needs a number or every swing qualifies. Mine is a wick at least twice the body and at least 1.5 times the average candle range of the previous 20 bars on the same timeframe.

On the full versus half wick question, there is a middle option I use. Entry at the 50 percent point of the wick, stop beyond the tip, so the stop stays where the full version puts it but the fill price improves.

The cost is missed trades, as mentioned above. On EURUSD 1H price often reacts a few pips inside the wick and never reaches the midpoint, so I keep a record of the misses to see what they would have paid.

I also only trade the first return to the zone. A wick zone that has already been touched and held once has used up some of the orders that made it, and the second visit was clearly weaker in the swings I marked.

When you mark the three most obvious wicks as suggested, do you include the ones made during Asia? Those look dramatic on the 1H but often come from very thin trading.
Shadow Trader
Posts: 5594
Joined: Wed Sep 09, 2026 5:19 pm

Re: Rejection Blocks, Trading the Wick Zone

Post by Shadow Trader »

Something I check before marking any 1H wick is how it was built on the 5M. A long upper wick can be a single spike that lasted two minutes, or forty minutes of price pushing into the same level and failing several times.

The second kind holds far better on the return in my notes. Repeated failures mean orders were actually defending the price, while a lone spike often just reflects one large market order hitting a thin book.

So I count the 5M candles with highs inside the wick zone. Three or more and the zone gets marked, one or two and I leave it alone, however dramatic it looks on the higher timeframe.

On FXS Prop Desk's point about gold, that is where this filter matters most. XAUUSD prints 1H wicks of 8 to 10 dollars on a single spike quite often, so a body to wick ratio on its own marks far too many zones there.

Fairman, do you treat a wick that formed across two 1H candles as one zone? A rejection that peaks at 10:58 can split over two bars and look like two ordinary candles.
Shadow Trader
Posts: 5594
Joined: Wed Sep 09, 2026 5:19 pm

Re: Rejection Blocks, Trading the Wick Zone

Post by Shadow Trader »

Draw a line at 1.0850 and price turns at 1.0847. Then it goes through 1.0852 and turns at 1.0856. Is the level wrong, or was the line too thin?

Many traders switch from lines to zones for exactly this reason. Markets don't respect exact prices. Orders spread across a range, and reactions tend to occur within an area, not at a single point.

Zones help with stop placement too, since a stop just beyond a line sits in the most crowded spot. A zone-based approach places stops beyond the whole area.

The downside is subjectivity. How thick should the zone be? Based on ATR, on previous wick sizes, on fixed pips?

One approach that bridges both: draw the line where the most recent touches clustered, then add a buffer equal to half the average candle wick size at that level. The result is a zone based on the pair's own behavior, not on an arbitrary number of pips, and it adjusts as volatility changes.

Which method gives better results, thin lines or thick zones, and how is zone width decided?
Post Reply