Advertisement IC Markets

20 EMA slope on M1 as a trend filter, how I read it without overcomplicating

Optimize MetaTrader 4, MetaTrader 5, cTrader, and TradingView for speed. Discuss Level II Market Depth (DOM), custom hotkeys, and volume indicators.
Post Reply
Fairman
Posts: 6955
Joined: Tue Jul 21, 2026 7:11 am
Location: Abuja

20 EMA slope on M1 as a trend filter, how I read it without overcomplicating

Post by Fairman »

20 EMA slope on M1 as a trend filter, how I read it without overcomplicating

I use the 20 EMA on M1 as a quick filter and I only care about its slope, not crossovers. If it's clearly angled up and price is staying above it, I'm only looking at longs. If it's angled down and price is below, only shorts. If it's flat and price is crossing it back and forth, I don't trade that pair at that moment.

The flat condition is the big one. Most of my bad scalps came in ranging conditions, where every entry looked fine in isolation but price just kept going sideways. A flat average is a simple visual that tells me it's one of those moments.

Entries are pullbacks toward the average with a rejection candle, and the stop goes beyond the pullback low or high. I don't buy when price is far from the line, because the stop would be too large and the move is already extended.

It's not a magic indicator. It lags, so you'll enter later than you want, but I would rather be late and trading with the flow than early and wrong. I check the M5 direction too, and if they disagree I stay out.
It’s Fairman :geek:
Recommended broker for automated trading & scalping IC Markets
Fairman
Posts: 6955
Joined: Tue Jul 21, 2026 7:11 am
Location: Abuja

Re: 20 EMA slope on M1 as a trend filter, how I read it without overcomplicating

Post by Fairman »

How I judge flat versus angled without overthinking it. I zoom so that about two hours of M1 candles fill the screen, then look at the line. If I need to tilt my head to decide whether it is sloping, it is flat. Clear slopes are obvious at a glance. I tried using an angle indicator to put a number on it, but it kept changing with the zoom level and the pair, and it ended up being more complicated than just looking.
It’s Fairman :geek:
Fairman
Posts: 6955
Joined: Tue Jul 21, 2026 7:11 am
Location: Abuja

Re: 20 EMA slope on M1 as a trend filter, how I read it without overcomplicating

Post by Fairman »

On the M5 agreement point, I put the same 20 EMA on M5 and only take the M1 signal when both are sloping the same way. When M1 is up and M5 is down, I usually find M1 is just a pullback inside the bigger move, and those long entries tend to fail right where the M5 average is sitting. It cuts the number of trades quite a bit, but most of the ones it removes were the frustrating sideways ones anyway.
It’s Fairman :geek:
Shadow Trader
Posts: 5594
Joined: Wed Sep 09, 2026 5:19 pm

Re: 20 EMA slope on M1 as a trend filter, how I read it without overcomplicating

Post by Shadow Trader »

The zoom problem with angle tools goes away if the slope is measured in price instead of degrees. Take how far the 20 EMA moved over the last 10 bars and divide it by the average M1 range, so the number means the same thing on any pair.

Say the EMA rose 2 pips over 10 bars while the typical M1 bar is 1.5 pips. That is about 1.3 bar ranges of travel, while anything under roughly half a bar range would count as flat on this kind of rule.

One case the eye tends to miss is the slope left behind by a spike. A 10 pip burst pulls the line up hard, and it keeps rising for many bars while price sits sideways above it, so the filter says trend after the move is over.

Checking that price has made a new high in the last 10 or 15 bars alongside the slope catches most of those. If the line is rising but no new high has printed, the angle is mostly memory of the spike.

On the M5 agreement, does the M5 slope need to clear the same threshold, or just point the same way? A flat but slightly rising M5 line seems like it could let a lot of the sideways trades back in.
FXS Prop Desk
Posts: 1689
Joined: Wed Oct 07, 2026 9:52 am

Re: 20 EMA slope on M1 as a trend filter, how I read it without overcomplicating

Post by FXS Prop Desk »

The slope filter is a simple and effective idea. One way to make it objective is to measure the slope over a fixed number of bars, for example the difference between the current EMA value and the value five bars ago, in pips. That gives a number you can test instead of judging the angle by eye.

The flat zone is the most important part. Defining a minimum slope below which you stay out probably removes many of the losing trades, since ranging periods are where most M1 trend strategies give back money.
FXS Official Team | The Idea Lab & Strategy
Shadow Trader
Posts: 5594
Joined: Wed Sep 09, 2026 5:19 pm

Re: 20 EMA slope on M1 as a trend filter, how I read it without overcomplicating

Post by Shadow Trader »

A slope filter also has a blind spot right at the turn, because of the lag in the average itself. A 20 EMA on M1 trails price by roughly ten bars, so its slope describes where price was, not where it is going.

Say price climbs 0.5 pips a bar for 40 bars and then falls at the same rate. In the chart (illustration), the EMA keeps rising for 6 bars after the top, and the five bar difference FXS Prop Desk suggested stays positive for 8 bars, when price is already 4 pips off the high.
img_13527_r2.png
img_13527_r2.png (91.97 KiB) Viewed 174 times
The nasty part is what price does during those bars. It falls back to the rising line 7 bars after the top, which looks exactly like the textbook pullback long, and that touch is really the first leg of the reversal.

Requiring a fresh high within the last 10 bars does not save this one, since the top is still inside that window. Waiting for a higher low to print after the touch does, because in this made up path it never comes.

How do you handle the touch when M5 still points up? In a turn like this the M5 line lags even longer, so the agreement check would also say buy.
Post Reply