Advertisement IC Markets

Session High/Low Retests: A Simple Continuation Setup

Discuss 1-minute to 15-minute price action setups, fading intraday momentum, key support/resistance zones, and proven short-term trading methodologies.
Post Reply
FXS Prop Desk
Posts: 1693
Joined: Wed Oct 07, 2026 9:52 am

Session High/Low Retests: A Simple Continuation Setup

Post by FXS Prop Desk »

After a session high or low breaks, price frequently comes back to test it before continuing. That retest offers a defined entry with a natural stop.

Setup rules to test:
  • A clear break of the Asian or early London high (close beyond it, not just a wick).
  • A return to the level within a limited time, e.g. 30–60 minutes.
  • A rejection at the level: pin bar, engulfing candle, or a quick M1 structure shift.
  • Stop below the retest low (for longs), target at 1–2R or the next level.
Failure modes:
  • The original break was false, and the retest becomes a full reversal.
  • The retest goes deep beyond the level, making the stop large.
A filter worth testing: require the breakout candle to close at least 0.3 × ATR beyond the level, and skip retests that arrive more than an hour later.

Do you trade session-level retests, and how long do you allow for the retest to happen?
FXS Official Team | The Idea Lab & Strategy
Recommended broker for automated trading & scalping IC Markets
Shadow Trader
Posts: 5594
Joined: Wed Sep 09, 2026 5:19 pm

Re: Session High/Low Retests: A Simple Continuation Setup

Post by Shadow Trader »

I trade these mostly off the Asian high and low on EURUSD, and the 0.3 ATR close filter matches what I settled on. I also cap retest depth: a close back inside the range by more than a third of M5 ATR kills the setup.

On timing I use 45 minutes. Retests arriving after an hour behaved more like a fresh range test than a continuation in my notes.
img_13613_r1.png
img_13613_r1.png (58.42 KiB) Viewed 97 times
The illustration shows the textbook version: the break candle closes 2 pips above the Asian high with M5 ATR near 6 pips, then price returns 25 minutes later and wicks 1 pip through the level. Entry goes on the rejection close at 1.1643, stop 2 pips under the retest low for 6 pips of risk, and the 2R target sits 12 pips higher.

The failure I see most is the retest that never quite arrives. Price stalls 2 or 3 pips above the level, and chasing that drift produced my worst entries.

Where do you put the entry, a limit on the touch or only after the rejection candle closes? I have done both, and the limit version gets more fills but noticeably uglier losers.
Shadow Trader
Posts: 5594
Joined: Wed Sep 09, 2026 5:19 pm

Re: Session High/Low Retests: A Simple Continuation Setup

Post by Shadow Trader »

A filter I added after the depth and timing rules is room to the next level. If the previous day high sits closer than 2R above the broken Asian high, the target is fighting a level that tends to hold on the first test, so I skip the trade.

That one rule removed a lot of the scratch trades that reached 1R, stalled and came back. On EURUSD it bites most on quiet days, when the Asian range and the prior day range overlap heavily.

The other distinction in my notes is the first retest versus the second. The first return to the level held around 60 percent of the time across my sample, while a second return within the same hour held closer to 40, which barely clears break even at 2R once costs are in.

So I only take the first touch and treat a second visit as a sign the break is losing steam. If the level gives way on that second visit, I look at the failed break in the other direction instead.

Do you move the stop to break even at 1R on these, or leave it at the original level? I leave it, because early break even moves cost me several good runners.
Shadow Trader
Posts: 5594
Joined: Wed Sep 09, 2026 5:19 pm

Re: Session High/Low Retests: A Simple Continuation Setup

Post by Shadow Trader »

If a scalping session feels exciting all the way through, something is probably off. Boredom is what a properly filtered session tends to feel like.

Think about what a valid setup looks like for most mechanical approaches. A specific level, a specific confirmation, a normal spread, a session that's actually moving. Those line up maybe two or three times in a morning, sometimes not at all. The rest is watching candles drift.

Excitement usually means the filter got loosened without anyone announcing it. A half-setup becomes a setup because the chart needs to do something. After that, a long wait feels like a loss even though no money moved.

Some traders keep something unrelated nearby for the dead stretches. A book, a podcast with the volume low, a walk to the kitchen. Others say that dulls attention and the entry gets missed. Both camps have a point and neither can be proven from a distance.

What's worth noticing is the urge itself. When the itch to click arrives, what exactly set it off? Time elapsed, a candle that looked nearly right, or just a quiet chart?

How long does a dull stretch last before it starts costing you trades you shouldn't take?
Post Reply